By combining numerical finite element analysis with analytical mechanical calculations and physical laboratory experiments, the team showed that tuning encapsulation thickness allows engineers to align the internal zero-strain neutral layer directly with fragile electrical layers. In a representative three-layer system, optimizing a deposited silicon nitride capping layer slashed the critical failure bending radius of a vulnerable electrode from 3.0 millimeters down to 1.5 millimeters, effectively cutting the device failure radius by fifty percent under tensile bending conditions.
Flexible electronic systems such as organic light-emitting diode displays rely on complex stacks of heterogeneous thin films, where functional semiconductor and conductive layers are layered alongside organic polymeric substrates and protective encapsulation barriers. While flexible organic polymers withstand substantial mechanical flexure, the functional inorganic constituents—specifically transparent conductive oxides like indium tin oxide and inorganic barrier films like silicon nitride or silicon oxide—are inherently brittle and susceptible to fracture. When subjected to external bending, stretching, or compressive deformation, these inorganic layers frequently suffer from channel cracking, interfacial delamination, or compressive buckling. Because transparent conductive layers carry electrical currents essential for display operation, mechanical rupture triggers abrupt spikes in electrical resistance, leading to partial circuit interruption or total device failure. Protecting brittle materials from mechanical breakdown under tight bending curvatures remains a fundamental design challenge for the mass adoption of foldable technology.
To mitigate stress accumulation in brittle layers, mechanical engineers utilize neutral axis engineering, which exploits the fundamental mechanics of bending in layered composites. When a multi-layer beam or film is bent, the outer convex surface experiences longitudinal tensile strain while the inner concave surface experiences compressive strain. Between these two opposing mechanical regimes lies a continuous structural plane known as the neutral layer, where the longitudinal normal strain equals zero. In classic three-layer and multi-layer mechanics, the exact vertical location of this zero-strain plane is governed strictly by the thickness, Young’s modulus, and Poisson’s ratio of each constituent layer under pure cylindrical bending conditions. If a fragile conductive material like indium tin oxide is placed directly at or very near this neutral plane, the mechanical strain imposed during tight curvature drops toward zero, shielding the brittle film from destructive crack initiation.
In their investigation, the research team analyzed the strain distribution across composite architectures using analytical models formulated for stacked films alongside finite element simulations implemented in ABAQUS. Assuming isotropic elastic properties, perfect interfacial bonding, defect-free layers, and pure cylindrical bending, theoretical formulations confirmed that bending strain varies linearly through the composite thickness. Numerical simulations revealed that as the thickness or Young’s modulus of an upper packaging film increased, the position of the neutral axis shifted systematically upward from the substrate toward the top surface of the device. When the packaging film and polyimide substrate shared identical mechanical moduli, the neutral layer settled precisely at the geometric mid-plane of the composite stack. However, varying the Young’s modulus of the capping layer also displaced the neutral layer toward stiffer regions, although achieving a comparable geometric shift via modulus modulation required substantial stiffness disparities, identifying thickness optimization as the far more practical engineering parameter.
The researchers applied these computational findings to optimize a practical flexible electrode architecture consisting of a flexible polyimide substrate, a thirty-nanometer indium tin oxide electrode layer, and a protective silicon nitride encapsulation layer deposited via plasma-enhanced chemical vapor deposition. Nanoindentation testing established the elastic modulus of the silicon nitride film at approximately 249 gigapascals, while the underlying polyimide substrate possessed a modulus of 1.44 gigapascals at a fifty-micrometer thickness. In dynamic bending experiments using a custom-built laboratory testing apparatus, unencapsulated indium tin oxide electrodes exhibited catastrophic crack propagation when electrical resistance increased by ten percent, establishing an empirical tensile failure stress threshold of 1.9 gigapascals. Through iterative numerical modeling at sub-micrometer increments, the researchers calculated that depositing a silicon nitride encapsulation layer with an optimal thickness of exactly 4.25 micrometers reduced the maximum internal stress in the conductive film to 0.3 megapascals. Subsequent physical bending tests confirmed that this thickness-tuned composite tolerated bending down to a 1.5-millimeter radius without electrical failure, compared to a 3.0-millimeter threshold before structural optimization.
While single neutral layer engineering successfully isolates one delicate functional layer, modern multi-functional electronics incorporate multiple brittle conductive and barrier layers distributed across varying depths of the structural stack. A conventional monolithic stack possesses only a single zero-strain plane, meaning that positioning one layer at the neutral axis inevitably displaces other fragile layers into high-strain tensile or compressive zones. To resolve this structural constraint, the researchers implemented a multiple neutral layer strategy by introducing optical clear adhesive interlayers. Rather than exhibiting a continuous linear strain distribution across the entire composite thickness, the adhesive decouples deformation across interfaces, generating independent, localized neutral planes within each individual structural sub-unit.
To rigorously capture the non-linear mechanics of the adhesive interlayers during finite element modeling, the team characterized commercial optical clear adhesive using rotational rheometer measurements. Experimental nominal stress-strain curves demonstrated pronounced strain-stiffening behavior under large shear deformations, which was accurately parameterized using a third-order hyperelastic Yeoh constitutive formulation with negative higher-order coefficients. Viscoelastic stress relaxation tests conducted under small shear strain revealed time-dependent exponential decay that plateaued without fully relaxing to zero stress, modeled via generalized Maxwell Prony series expansions. When implemented in finite element simulations, the low-modulus adhesive effectively isolated the adjacent structural films. As the adhesive thickness increased from twenty-five to five hundred micrometers, tensile strain on the outer film surface decreased and plateaued, while variations in adhesive modulus proved critical: maintaining a sufficiently low elastic modulus ensured multiple neutral layers formed, whereas artificially elevating the adhesive modulus to four gigapascals collapsed the independent neutral planes back into a single monolithic linear strain profile.
The decoupling mechanics of optical clear adhesive were subsequently evaluated in multilayer sandwich electrode configurations and dual-electrode circuits subjected to experimental dynamic bending tests. In sandwich structures comprising polyimide substrates, optical clear adhesive, and flexible electrodes, reducing the polyimide film thickness from one hundred to twenty-five micrometers decreased the failure radius from approximately 6.5 millimeters to 3 millimeters, corroborating numerical predictions that thinner constituent films minimize surface strains. Furthermore, varying adhesive thicknesses between twenty-five and one hundred micrometers produced nearly identical electrode failure radii, confirming that interfacial decoupling is predominantly governed by the low shear modulus of the adhesive rather than its geometric thickness, provided the adhesive layer maintains structural integrity against interfacial shear delamination.
To demonstrate practical functional performance in complex multi-layer devices, the researchers fabricated dual-layer flexible electrodes incorporating two independent indium tin oxide conductive traces connected to miniature indicator light bulbs. In a control structure assembled using double-sided polyimide tape with an elastic modulus of 475 megapascals, numerical simulations revealed a single neutral axis positioned near the tape center, subjecting the upper electrode to an extreme tensile strain of 5.6 percent and the lower electrode to 5.5 percent compressive strain at a 4.5-millimeter bending radius. Conversely, assembling the dual-electrode system using low-modulus optical clear adhesive established two distinct neutral layers positioned directly adjacent to both conductive traces. Finite element calculations indicated that strain in both indium tin oxide layers dropped from 5.6 percent to near zero, while the peak strain on the outermost tape layer decreased from 10.2 percent to 3.1 percent.
Physical testing of the optical-adhesive-bonded dual-electrode system verified dramatic gains in electrical and mechanical reliability under tight curvature. When bent to a 4.5-millimeter radius, both indicator bulbs remained brightly illuminated, and the assembly sustained mechanical flexing down to failure radii of 2.5 millimeters and 3.0 millimeters for the upper and lower electrodes, respectively. The combined theoretical calculations, computational simulations, and experimental evaluations provide comprehensive mechanical guidelines for flexible electronic design, demonstrating that coordinating single neutral layer thickness tuning with multiple neutral layer adhesive decoupling provides a robust foundation for building highly durable foldable and rollable electronic devices.
Subject of Research: Mechanical optimization of neutral layers and optical adhesives for flexible electronics bendability
Article Title: Optimizing bendability of flexible electronic devices using a neutral layer strategy
Article References: Wu, M., Jian, M., Zhang, J., & Yang, L. (2025). Optimizing bendability of flexible electronic devices using a neutral layer strategy. Moore and More, 2(1), Article 2. https://doi.org/10.1007/s44275-024-00019-8
Image Credits: AI Generated
DOI: 10.1007/s44275-024-00019-8
Keywords: flexible electronics, neutral layer strategy, neutral axis engineering, indium tin oxide, finite element analysis, optical clear adhesive, silicon nitride encapsulation, polyimide substrate, bending failure radius, mechanical strain reduction, flexible displays, OLED durability, thin film encapsulation, viscoelastic relaxation, hyperelastic modeling, shear strain decoupling
Cite Scienmag News
Denise Maddox. (November 19, 2026). Neutral Layer Engineering Cuts Flexible Electrode Bending Failure Radius by Half. Scienmag. https://scienmag.com/neutral-layer-engineering-cuts-flexible-electrode-bending-failure-radius-by-half/
Denise Maddox. "Neutral Layer Engineering Cuts Flexible Electrode Bending Failure Radius by Half." Scienmag, 19 November 2026, https://scienmag.com/neutral-layer-engineering-cuts-flexible-electrode-bending-failure-radius-by-half/. Accessed 19 November 2026.
Denise Maddox. "Neutral Layer Engineering Cuts Flexible Electrode Bending Failure Radius by Half." Scienmag. November 19, 2026. https://scienmag.com/neutral-layer-engineering-cuts-flexible-electrode-bending-failure-radius-by-half/








