Vertically integrated bilayer metasurfaces suppress unwanted optical reflection down to 1.2 percent while maintaining complete 0 to 2π transmission phase coverage and diffraction-limited focusing. In experimental demonstrations operating at a near-infrared wavelength of 1,310 nanometers, free-standing titanium dioxide bilayer metalenses suppressed reflection below that of bare glass and eliminated 76 percent of the total reflection loss found in conventional single-layer devices. Whereas a standard single-layer device exhibited a reflectance of 5.1 percent, the engineered bilayer architecture reduced this value substantially and redirected the recovered optical power directly into the focal point. By showing that bilayer meta-atoms can simultaneously function as phase shifters and impedance-matching stacks, the research establishes a practical platform for jointly engineering optical impedance and wavefront response at the level of individual meta-atoms.
Antireflection coatings are standard components in optical systems, where they are routinely employed to enhance light transmission and suppress reflections by matching optical impedance across a uniform material interface. Applying this conventional concept to metasurfaces is fundamentally challenging because metasurface wavefront control relies on dense arrays of geometrically distinct meta-atoms. These varying nanostructures present a spatially inhomogeneous optical impedance across the surface of the flat optic. Vertical integration overcomes this limitation by breaking the tether between wavefront control and optical impedance. By allowing bilayer meta-atoms to act concurrently as wavefront phase-shifting elements and impedance-matching stacks, the vertical approach addresses reflection locally at each individual nanostructure rather than attempting to apply a uniform external treatment across contrasting elements.
To implement this local impedance matching, the investigators treated the individual meta-atoms as multilayer thin films. Through this thin-film physical framework, they derived a dedicated design rule that directly links the effective refractive indices of two independently patterned constituent layers. This systematic design rule identified antireflective bilayer libraries capable of achieving full zero to 2π transmission phase coverage across the entire device. Rather than relying on traditional post-fabrication coating treatments applied to a finished optic, this formulation fundamentally shifts antireflection into a primary metasurface design principle. Within this framework, the phase library itself is impedance matched, ensuring that each structural unit provides the requisite local phase shift without introducing significant reflective losses.
The experimental devices were fabricated on 500-micrometer-thick fused-silica substrates using damascene nanofabrication techniques. Single-layer control metalenses and bilayer metalenses were realized via single-damascene and double-damascene processes, respectively. During the fabrication sequence, the first titanium dioxide layer was defined using electron-beam lithography in 950 PMMA A8 resist, subsequently filled with titanium dioxide via atomic layer deposition performed at 90 degrees Celsius, and planarized using reactive-ion etch back. For the bilayer metalenses, this entire deposition and planarization sequence was repeated using ZEP520A as the second resist layer, which was developed in cold o-xylene at 5 degrees Celsius. The process concluded with oxygen plasma ashing to remove the remaining resist material and yield clean, free-standing bilayer titanium dioxide pillars.
To maintain rigorous experimental control and eliminate fabrication variability, both the single-layer control and the bilayer metalenses were fabricated on the exact same fused-silica substrate. The single-layer control device underwent the complete second-layer processing sequence alongside the bilayer device, but without receiving any pattern exposure during lithography. This controlled procedure ensured that both the single-layer baseline and the bilayer metalenses experienced identical first-layer processing conditions, thermal histories, and chemical post-processing environments. Consequently, any observed differences in reflectance, transmission efficiency, and focal spot characteristics could be attributed strictly to the patterned vertical bilayer architecture rather than extraneous substrate-to-substrate variations or differences in fabrication handling.
Optical characterization of the fabricated metalenses was conducted using a dedicated experimental setup illuminated by a tunable light source. The optical train incorporated an NKT Photonics SuperK laser coupled to a Photon etc. LLTF filter, providing tunable illumination that was collimated and focused directly onto the metalens aperture. The transmitted focal field generated by the metalens was collected using a Mitutoyo M Plan Apo near-infrared 50-times objective with a numerical aperture of 0.42. The collected light was subsequently relayed through a tube lens and captured on a Raptor OWL 640 near-infrared camera. Focusing efficiencies across the optical aperture were evaluated against a substrate-normalized reference following standardized measurement methodologies.
The substrate-normalized reference power was determined by translating the sample stage to an unpatterned region of the same fused-silica substrate and recording the transmitted beam profile under identical illumination conditions. Transmitted focal power was integrated over a circular aperture of diameter D3 equal to approximately 3.24 times the wavelength divided by the numerical aperture, which corresponds to the third zero of the Airy pattern. This focal power value was normalized against the reference intensity integrated over a 250-micrometer circular mask matching the physical device aperture. All reported efficiency values represent averages calculated over 100 separate camera frames, while Strehl ratios were extracted from peak point spread function intensities following normalization to an ideal diffraction-limited Airy profile at the matching numerical aperture.
The authors noted that their current demonstration represents a forward-design recipe implemented on a specific titanium dioxide material platform, leaving clear opportunities for future optimization. The design space could be substantially expanded by incorporating hybrid materials, which provide access to a broader range of effective refractive indices. Pairing hybrid material platforms with computational inverse design techniques could enable further optimization of reflectivity alongside broadband operating bandwidths and wide-angle responses. Additionally, the metasurface architecture can be extended laterally by adopting complex nanopillar geometries such as free-form shapes, or vertically by incorporating more stacked layers to enrich Bloch mode interactions across each optical interface, bringing vertically integrated flat optics closer to nearly lossless performance.
Subject of Research: Antireflective bilayer metasurfaces for optical impedance matching and wavefront control
Article Title: Antireflective bilayer metasurfaces with complete wavefront control
Article References: Oh, J., Cassara, D., Palmieri, A., Piatti, L., Rodrigues, J. R., Dorrah, A. H., Dainese, P., & Capasso, F. (2026). Antireflective bilayer metasurfaces with complete wavefront control. Nature Nanotechnology. https://doi.org/10.1038/s41565-026-02330-x
Image Credits: AI Generated
DOI: 10.1038/s41565-026-02330-x
Keywords: bilayer metasurfaces, optical impedance matching, wavefront control, antireflection, metalenses, titanium dioxide, transmission phase coverage, near-infrared optics, diffraction-limited focusing, double-damascene process, electron-beam lithography, atomic layer deposition, Strehl ratio, Airy pattern, Bloch modes, fused-silica substrate, free-standing nanopillars
Cite Scienmag News
Denise Maddox. (November 20, 2026). Bilayer Metasurfaces Reduce Reflection Loss While Maintaining Complete Optical Wavefront Control. Scienmag. https://scienmag.com/bilayer-metasurfaces-reduce-reflection-loss-while-maintaining-complete-optical-wavefront-control/
Denise Maddox. "Bilayer Metasurfaces Reduce Reflection Loss While Maintaining Complete Optical Wavefront Control." Scienmag, 20 November 2026, https://scienmag.com/bilayer-metasurfaces-reduce-reflection-loss-while-maintaining-complete-optical-wavefront-control/. Accessed 20 November 2026.
Denise Maddox. "Bilayer Metasurfaces Reduce Reflection Loss While Maintaining Complete Optical Wavefront Control." Scienmag. November 20, 2026. https://scienmag.com/bilayer-metasurfaces-reduce-reflection-loss-while-maintaining-complete-optical-wavefront-control/








