A research team has demonstrated an optical, non-destructive method for estimating the nanoscale thickness of polymer thin films using ultraviolet-visible spectrophotometry, offering an accessible alternative to complex physical profilometry. Thin polymer coatings deposited onto engineering substrates serve critical protective and functional roles across various fields, including corrosion protection, wear resistance, electrical insulation, solid lubrication, and biomedical engineering. In these settings, coating performance depends heavily on film thickness, which dictates optical, mechanical, and barrier characteristics. While microbalance methods, electrical testing, radiation-based tools, and chemical analysis can monitor thin layers, their cost and complexity frequently restrict routine testing. By measuring absorbance, transmittance, and reflectance across the 340 to 540 nanometer wavelength spectrum, the investigators determined essential optical constants and correlated them with polymer concentrations, film thicknesses, and wetting properties.
The study evaluated four distinct water-soluble synthetic polymers: polyvinyl alcohol, polyethylene glycol, polyacrylamide, and polyvinyl acetate. Each polymer possesses unique structural properties and practical industrial uses. Polyvinyl alcohol is a synthetic resin widely employed in the treatment of textiles and paper, distinguished by the fact that it is not synthesized directly from single-unit precursor monomers. Polyacrylamide is a water-soluble acrylic polymer extensively utilized in urban and industrial wastewater treatment processes. Polyethylene glycol is a versatile polyether compound with applications extending across agriculture and medicine. Polyvinyl acetate is a rubbery synthetic polymer possessing the molecular formula C4H6O2. By assessing four polymers with diverse chemical backbones, the researchers examined how variations in polymer structure and chain mobility influence film growth and surface energetics on standard glass substrates.
To prepare the test specimens, the investigators dissolved each polymer in distilled water across ten defined concentration levels ranging from 20 grams per cubic decimeter to 110 grams per cubic decimeter, incremented at intervals of 10 grams per cubic decimeter. Because one gram per cubic decimeter equals one gram per liter, this range established a wide spectrum of solute concentrations. Masses were verified with a digital analytical balance before dissolution. Small glass slides measuring 25 millimeters by 76 millimeters by 1 millimeter served as the deposition substrates. The researchers applied each solution onto the glass slides via drop casting using a dropper to distribute controlled droplet volumes evenly before sun drying. While drop casting can yield non-uniform drying profiles, controlled droplet volumes and spreading were maintained to support consistent film formation prior to capping and subsequent spectroscopic evaluation.
Optical measurements were conducted using a visible MetaSpec AE1405031 Pro spectrophotometer situated at Nnamdi Azikiwe University in Awka, Anambra State. Absorbance and transmittance values were gathered across the 340 nanometer to 540 nanometer range at precise 1 nanometer increments. From these experimental profiles, the researchers derived the absorption coefficient, reflectance, extinction coefficient, and the real and imaginary parts of the complex refractive index. Reflectance was determined indirectly from absorbance and transmittance data, while the extinction coefficient was calculated using the incident light wavelength and the absorption coefficient. Mathematical formulations relating the absorption coefficient to absorbance and path length enabled direct calculation of the estimated film thickness. When multiple absorbance peaks appeared across the spectrum, the primary maximum was selected because it represents the dominant electronic transition with the strongest signal-to-noise ratio, whereas minor secondary peaks caused by scattering, overtone absorptions, or surface inhomogeneities were excluded.
Spectrophotometric readings revealed distinct optical signatures and absorbance maxima for each polymer across the measured spectrum. Peak absorbance values ranged from 0.148 to 0.368 for polyvinyl alcohol, 0.159 to 0.590 for polyethylene glycol, 0.287 to 0.990 for polyacrylamide, and 0.012 to 0.052 for polyvinyl acetate. Polyvinyl alcohol exhibited moderate absorption with its primary peak centered at 480 nanometers, corresponding to electronic transitions along the polymer backbone. Polyethylene glycol displayed multiple absorption bands with a prominent maximum at 420 nanometers, reflecting functional group interactions. Polyacrylamide generated the highest overall absorbance among all tested polymers, displaying a sharp, intense band at 420 nanometers indicative of strong electronic transitions. In contrast, polyvinyl acetate showed weak optical absorption across the entire 340 to 540 nanometer range with a modest peak at 340 nanometers, attributable to its molecular architecture and absence of strong chromophoric groups.
Calculations of film thickness revealed diverging growth behaviors as polymer concentration increased. For polyethylene glycol and polyacrylamide, thickness scaled positively with solution concentration. Polyethylene glycol films expanded from approximately 0.7 nanometers at 20 grams per cubic decimeter to 5.5 nanometers at 100 grams per cubic decimeter, with calculated values reaching up to 6.25 nanometers, driven by increased chain entanglement and solution viscosity that supported dense film buildup. Polyacrylamide exhibited the most pronounced thickness increase, rising from roughly 1.5 nanometers to nearly 9 nanometers, with values spanning 0.74 nanometers at 30 grams per cubic decimeter to 8.86 nanometers at 90 grams per cubic decimeter. A linear regression fit for polyacrylamide produced a coefficient of determination of 0.8489, confirming that approximately 85 percent of the variance in thickness was explained by solution concentration, reflecting greater particle accumulation and dense molecular packing during deposition.
Conversely, polyvinyl alcohol and polyvinyl acetate showed negative or highly constrained thickness responses to increasing concentration. Polyvinyl alcohol exhibited an inverse trend where calculated thickness decreased from approximately 2.5 nanometers down to 1.0 nanometers as concentration rose from 20 to 100 grams per cubic decimeter, spanning absolute values between 2.90 nanometers and 0.25 nanometers. This inverse trend was attributed to elevated solution viscosity at high concentrations, which hindered fluid spreading and leveling on the glass slide and resulted in uneven, thinner deposited layers upon drying. Polyvinyl acetate displayed a moderate inverse correlation with an R-squared value of 0.723, with thickness decreasing from 4.9 nanometers to 3.6 nanometers across the 10 to 100 grams per cubic decimeter range, maintaining an overall tight band between 4.12 nanometers and 4.97 nanometers. The researchers linked this behavior to acetate functional groups altering polymer-solvent and substrate interactions.
Surface wetting behavior was evaluated by placing two-microliter droplets of distilled water onto dried films using a Ramé-Hart Model 210 contact angle goniometer, capturing angles within five seconds to mitigate evaporation artifacts. Contact angle measurements indicated clear structural divergences among the polymers. For polyvinyl alcohol and polyethylene glycol, contact angles were highest at lower absorbance levels and decreased with increasing polymer content, signifying enhanced surface hydrophilicity before plateauing at elevated concentrations. Conversely, polyacrylamide and polyvinyl acetate exhibited positive correlations between contact angle and absorbance. In polyacrylamide films, the water contact angle increased markedly from 64 degrees to 90 degrees with greater thickness, indicating a transition toward a hydrophobic, poorly wetted surface caused by the formation of dense, gel-like aggregates. In polyvinyl alcohol films, contact angles decreased from 72 degrees down to 57 degrees, demonstrating increased wettability.
Surface free energy analysis, calculated via the Owens-Wendt model using distilled water and diiodomethane probe liquids, provided further insight into surface polarity. Across the four materials, total surface free energy generally decreased as film thickness increased, reflecting reduced molecular mobility and fewer available polar interaction sites at the film interface. Polyvinyl acetate exhibited the highest surface free energy among all polymers, maintaining values between 65.80 and 70.60 millijoules per square meter, indicative of high surface polarity. Polyethylene glycol maintained stable surface energy values between 48.85 and 54.60 millijoules per square meter. In contrast, polyacrylamide displayed a pronounced decline in surface free energy from 53.49 millijoules per square meter down to 41.05 millijoules per square meter as thickness increased, mirroring the formation of less polar, hydrophobic outer surface layers.
The study demonstrates that standard spectrophotometric absorbance and transmittance data, processed through fundamental optical relations, can estimate nanoscale polymer film thickness and infer corresponding surface energetic properties without requiring destructive testing or specialized profilometers. The investigators noted that the drop-casting technique introduced inherent thickness variations and that the calculations relied on indirect optical modeling within a narrow visible wavelength window. To advance the technique, future investigations should expand the monitored spectral range, refine wavelength resolution, and directly validate spectrophotometric thickness calculations against physical characterization techniques such as contact profilometry and spectroscopic ellipsometry.
Subject of Research: Spectrophotometric estimation of polymer film thickness and surface properties
Article Title: Estimation of film thickness of a polymer using spectrophotometric data
Article References: Odeh, C. P., Ilechukwu, A. E., Okeke, J. C., Chikelu, P. O., & Madumere, A. U. (2025). Estimation of film thickness of a polymer using spectrophotometric data. Journal of Materials Science: Composites, 6(1), Article 15. https://doi.org/10.1186/s42252-025-00077-7
Image Credits: AI Generated
DOI: 10.1186/s42252-025-00077-7
Keywords: UV-Vis spectrophotometry, polymer thin films, film thickness estimation, polyvinyl alcohol, polyethylene glycol, polyacrylamide, polyvinyl acetate, surface free energy, contact angle, drop casting, optical constants, refractive index, absorbance spectroscopy, extinction coefficient, coatings engineering, thin film characterization
Cite Scienmag News
Neil Sanderson. (November 21, 2026). Spectrophotometric Analysis Estimates Polymer Coating Thickness and Surface Wetting Behavior. Scienmag. https://scienmag.com/spectrophotometric-analysis-estimates-polymer-coating-thickness-and-surface-wetting-behavior/
Neil Sanderson. "Spectrophotometric Analysis Estimates Polymer Coating Thickness and Surface Wetting Behavior." Scienmag, 21 November 2026, https://scienmag.com/spectrophotometric-analysis-estimates-polymer-coating-thickness-and-surface-wetting-behavior/. Accessed 21 November 2026.
Neil Sanderson. "Spectrophotometric Analysis Estimates Polymer Coating Thickness and Surface Wetting Behavior." Scienmag. November 21, 2026. https://scienmag.com/spectrophotometric-analysis-estimates-polymer-coating-thickness-and-surface-wetting-behavior/








