A research team from Suzhou University, Qingdao University of Technology, and collaborating institutions has demonstrated that combining triethanolamine with agricultural straw ash produces a high-performance cementitious grouting material when proportioned through mathematical response surface modeling. Investigating structural repair and geotechnical reinforcement composites, the researchers applied a three-factor, three-level Box-Behnken experimental design to evaluate how varying dosages of triethanolamine, straw ash replacement levels, and water-to-cement ratios govern both fresh grout fluidity and hardened mechanical properties. Cement-based grouting slurries are critical engineering components deployed under pressure into underground fractures, rock cavities, foundation reinforcements, and structural anchorage systems. Meeting the demanding operational criteria of modern engineering requires strict simultaneous control over fresh slurry workability, volumetric stability, and ultimate mechanical capacity, especially when conventional formulations must be reconciled with sustainable resource conservation.
The study addressed a fundamental materials science challenge arising from the complex chemico-physical interactions between chemical setting accelerators and supplementary pozzolanic materials. Triethanolamine functions as an organic chemical accelerator that selectively modifies the hydration kinetics of individual clinker compounds, catalyzing tricalcium aluminate reactions while temporarily retarding the dissolution of calcium silicates. Concurrently, agricultural straw ash introduces reactive amorphous silica that consumes portlandite produced during clinker hydration to deposit secondary calcium silicate hydrate and calcium aluminosilicate hydrate gels. Because these concurrent phenomena display nonlinear interdependencies that traditional single-variable experimental approaches cannot resolve, the researchers implemented statistical response surface methodology to evaluate factor interactions and determine optimal proportions.
To establish the empirical models, the authors prepared experimental grouts conforming to standard testing specifications using Grade PO 42.5 ordinary Portland cement, potable tap water, and natural river sand possessing a fineness modulus of 2.8. Chemical acceleration was provided by analytical-grade triethanolamine with a purity exceeding 99 percent, while fresh mix workability was maintained using a polycarboxylate-based superplasticizer possessing a solid content of 20.5 percent and a water reduction efficiency exceeding 30 percent. Under the Box-Behnken design matrix, the researchers established seventeen distinct mix proportions across three designated factor levels: straw ash replacement at 10, 15, and 20 percent; triethanolamine dosages of 0.3, 0.5, and 0.7 percent; and water-to-cement ratios of 0.30, 0.33, and 0.36. Prismatic specimens measuring 40 mm by 40 mm by 160 mm were molded, cured at 20 degrees Celsius and 95 percent relative humidity for 24 hours, demolded, and immersed in lime-saturated water until mechanical evaluation.
Mechanical testing of hardened specimens was conducted in strict accordance with standard GB/T 17671-1999 procedures using an electro-hydraulic servo testing system operating at a constant loading rate of 2.4 kilonewtons per second. Each proportion yielded six distinct compressive strength measurements taken from the fractured ends of three flexural prisms, producing a tight experimental coefficient of variation below 3 percent across all test groups. Across the preliminary seventeen design iterations, recorded slurry fluidity ranged from 281 mm to 310 mm, while 28-day compressive strengths spanned 42.1 MPa to 65.4 MPa. These baseline measurements confirmed that every trial formulation satisfied general structural grouting thresholds while establishing a wide performance spread suitable for comprehensive quadratic polynomial regression modeling.
Subsequent analysis of variance confirmed that the developed quadratic regression equations demonstrated high statistical significance, capturing experimental variances with determination coefficients exceeding 0.95 for both fluidity and 28-day compressive strength. Diagnostic screening revealed adequate precision ratios of 24.6 for fluidity and 31.2 for compressive strength, substantially surpassing the standard threshold of four and validating model suitability for navigating the experimental design space. The main effects analysis demonstrated that the water-to-cement ratio exerted the most pronounced primary influence on slurry fluidity, followed by triethanolamine dosage and straw ash content. Conversely, for 28-day compressive strength, all three primary variables exhibited highly significant individual influences, with p-values falling below 0.0001. The statistical evaluations indicated that quadratic terms and mutual factor interactions significantly influenced mechanical resistance, confirming that strength development does not follow a simple linear progression.
Three-dimensional response surface plots and contour mappings illustrated the nuanced interactions governing material behaviors within the design domain. At low straw ash contents, increasing triethanolamine dosage modestly enhanced fluidity, but this plasticizing effect diminished as ash concentrations rose. For compressive strength, interaction profiles exhibited distinct dome-shaped surfaces characterized by central optima. The maximal 28-day compressive resistance concentrated near a straw ash replacement level of 15 percent, a triethanolamine dosage of 0.60 to 0.65 percent, and a water-to-cement ratio of approximately 0.33.
To translate the empirical response surfaces into an optimized industrial mix, the team executed numerical multi-objective optimization using Design-Expert software, balancing peak mechanical resistance against target flowability. The algorithmic solver converged on an optimal mix proportion consisting of 0.65 percent triethanolamine, 5.0 percent straw ash replacement, and a water-to-cement ratio of 0.33. The predictive model calculated that this formulation would achieve a fresh slurry fluidity of 189.44 mm and a 28-day compressive strength of 34.59 MPa. To validate the mathematical predictions, the researchers conducted five independent experimental verification batches using the exact parameter set. The physical trials generated an average fluidity of 189.24 mm and an average compressive strength of 34.06 MPa. Both observed values exhibited a absolute deviation of less than 2.1 percent from model projections, substantially outperforming the 5 percent error limit established for experimental validation.
The microstructural mechanisms driving this macroscopic performance were investigated through Fourier transform infrared spectroscopy across five representative mix proportions cured for 3 days and 28 days. After halting hydration via 72-hour ethanol immersion and vacuum desiccation at 60 degrees Celsius, powder specimens were analyzed using potassium bromide pellets across the 4000 to 400 cm⁻¹ spectral band. At 3 days, prominent absorption bands at 3642 to 3644 cm⁻¹ evidenced crystalline calcium hydroxide, accompanied by an intense peak at 973 to 998 cm⁻¹ assigned to silicon-oxygen stretching within polymerized calcium silicate hydrate gels. Simultaneously, enhanced bands between 865 and 876 cm⁻¹ indicated that reactive aluminates actively participated in producing secondary hydration products, including ettringite and monosulfoaluminate phases.
Complementary X-ray diffraction patterns collected on a Rigaku SmartLab diffractometer over a 2-theta scanning interval of 5 to 65 degrees corroborated the hydration sequence across curing ages. At 3 days, diffraction spectra were dominated by prominent alite and belite clinker peaks between 29 and 34 degrees alongside sharp portlandite peaks at 18 and 34 degrees. By 28 days, clinker diffraction intensities dropped substantially, becoming nearly undetectable in high-ash, high-triethanolamine formulations. This phase depletion demonstrated that triethanolamine disrupted clinker passivation layers to accelerate ionic dissolution, while pozzolanic silica consumed dissolved calcium ions. Concurrently, early-formed ettringite detected at 9.1 degrees underwent desulfurization, converting into stable monosulfoaluminate at 11.6 degrees.
Despite the successful optimization of fresh workability and mechanical strength, the authors outlined critical durability constraints regarding agricultural biomass ash utilization. Uncontrolled carbonation degrades the durability of reinforced structures by reducing the alkaline pH of the pore fluid, which compromises the protective passivation layer surrounding embedded steel reinforcement. Furthermore, the researchers acknowledged that initial predictive models exhibited lower predicted determination coefficients compared to adjusted values, reflecting slight overfitting inherent to seventeen-run designs. Consequently, the authors concluded that straw ash incorporation should be restricted to moderate levels of 10 percent or less to balance strength gains against carbonation resistance in long-term engineering deployments.
Subject of Research: Optimization of cementitious grouting materials incorporating triethanolamine and agricultural straw ash
Article Title: Study on the performance of grouting materials prepared using TEA and straw ash based on response surface method
Article References: Wu, Z., Chu, J., Zhao, M., Luan, C., Pang, B., & Wang, W. (2026). Study on the performance of grouting materials prepared using TEA and straw ash based on response surface method. Frontiers in Physics, 14, 1932572. https://doi.org/10.3389/fphy.2026.1932572
Image Credits: AI Generated
DOI: 10.3389/fphy.2026.1932572
Keywords: grouting materials, triethanolamine, straw ash, response surface methodology, Box-Behnken design, compressive strength, slurry fluidity, cement hydration, pozzolanic reaction, calcium hydroxide consumption, ettringite transformation, Fourier transform infrared spectroscopy, X-ray diffraction, calcium silicate hydrate, agricultural waste valorization, multi-objective optimization, durability carbonation
Cite Scienmag News
Nora Hawkins. (November 13, 2026). Response Surface Method Optimizes Straw Ash and Triethanolamine in High-Performance Cement Grout. Scienmag. https://scienmag.com/response-surface-method-optimizes-straw-ash-and-triethanolamine-in-high-performance-cement-grout/
Nora Hawkins. "Response Surface Method Optimizes Straw Ash and Triethanolamine in High-Performance Cement Grout." Scienmag, 13 November 2026, https://scienmag.com/response-surface-method-optimizes-straw-ash-and-triethanolamine-in-high-performance-cement-grout/. Accessed 18 November 2026.
Nora Hawkins. "Response Surface Method Optimizes Straw Ash and Triethanolamine in High-Performance Cement Grout." Scienmag. November 13, 2026. https://scienmag.com/response-surface-method-optimizes-straw-ash-and-triethanolamine-in-high-performance-cement-grout/








