The starting materials belong to a family of cyanometallate coordination polymers with the general framework T[Fe(CN)₅NO], where T is a transition-metal ion. In the study, T was cobalt, nickel, or copper. Pyridine molecules bind to the outer metal centers and change the architecture from a three-dimensional bulk structure into layered two-dimensional sheets. This transformation is important because the parent nitroprussides have limited surface area and disperse poorly, whereas thin layers can be distributed across a conductive carbon support. Pyridine is therefore not introduced primarily as an oxygen-evolution promoter. Its principal role is structural: by selectively replacing axial metal–cyanide connections, it enables the layered morphology and helps stabilize neighboring sheets through pi–pi and dipole–dipole interactions. The resulting materials were combined with reduced graphene oxide in a one-to-one weight ratio. The graphene network provides pathways for electron transport and helps expose the coordination-polymer domains to the alkaline electrolyte.

Several complementary measurements confirmed that the metal identity altered both the structure and the electronic environment of the composites. X-ray diffraction showed layered materials with characteristic basal-plane reflections for the cobalt and nickel systems, while the copper composite displayed different stacking behavior. Electron microscopy revealed average particle sizes of approximately 133 nanometers for the cobalt material, 47 nanometers for the nickel material, and 214 nanometers for the copper material. Infrared and Raman spectroscopy detected the cyanide, nitrosyl, pyridine, and graphene-related signatures expected from the composite design. The cyanide stretching frequency shifted systematically as the metal changed from cobalt to copper, reflecting differences in the cations’ polarizing power. Raman measurements also indicated a defect-rich reduced graphene oxide support. The disorder can be useful in electrocatalysis because defects may create additional sites for oxygen-related reactions, although the measured surface area alone did not determine which composite performed best.

Electrochemical testing revealed a clear division of labor among the three materials. For OER in alkaline solution, the nickel composite showed the lowest onset potential and the strongest current response, reaching 10 milliamperes per square centimeter at an overpotential of about 398 millivolts. The cobalt and copper versions required approximately 437 and 518 millivolts, respectively, under the same benchmark. Nickel also exhibited the lowest charge-transfer resistance across the tested potential range. Cobalt, however, produced the lowest fitted OER Tafel slope, 61 millivolts per decade, compared with 74 for nickel and 156 for copper. The researchers caution that a lower Tafel slope by itself does not establish the fastest overall reaction; onset potential, overpotential, resistance, and operating conditions must be considered together. For ORR, the pattern reversed. The copper composite delivered the lowest onset potential and the highest limiting current, indicating the most favorable oxygen-reduction behavior among the tested materials.

Rotating-disk experiments provided further information about the oxygen-reduction pathway. Koutecky–Levich analysis indicated that all three composites predominantly followed a four-electron route, which is desirable in zinc-air batteries because it converts oxygen more directly and limits peroxide formation. The estimated electron-transfer numbers were approximately 3.95 for cobalt, 3.63 for nickel, and 3.97 for copper. The nickel value suggests that a mixture of four-electron and two-electron pathways may occur, potentially producing some hydrogen peroxide. The authors note that rotating-ring-disk measurements would be needed to investigate that possibility directly. Together, the half-cell results show why optimizing a rechargeable zinc-air battery is difficult: nickel favors the charging reaction, copper favors the discharging reaction, and neither is automatically the best complete-device material. The measurements instead point toward a compromise in which both reactions remain sufficiently active.

That compromise emerged when the composites were assembled into working zinc-air batteries. The cobalt-based cathode produced the highest peak power density, 54 milliwatts per square centimeter, narrowly exceeding the nickel system at 53 and clearly surpassing the copper system at 39. It also maintained higher discharge-voltage plateaus, particularly as the current density increased. During galvanostatic cycling at 10 milliamperes per square centimeter, the cobalt battery began with a voltage gap of 0.99 volts between charge and discharge and reached 1.18 volts after 24 hours. The corresponding gaps for copper were 1.05 and 1.29 volts, while nickel showed 1.43 and 1.36 volts. Initial round-trip energy efficiencies were 52 percent for cobalt, 50 percent for copper, and 34 percent for nickel. After the cycling period, they were 46, 42, and 33 percent, respectively. The cobalt device also retained a relatively stable impedance and delivered an average energy above 8.5 watt-hours per square meter per cycle.

The study’s central chemical finding is that the synthesized nitroprussides do not remain unchanged during battery operation. Post-cycling analysis of the best-performing cobalt electrode showed that the characteristic cyanide signal disappeared, while hydroxyl and metal–oxygen signatures emerged. X-ray diffraction and Raman spectroscopy likewise indicated conversion into a cobalt hydroxide or oxyhydroxide phase. The original material is therefore a precursor rather than the final catalyst. Importantly, X-ray photoelectron spectroscopy detected a pyridinic nitrogen signal after cycling, suggesting that the pyridine ligand remained associated with the reconstructed active phase instead of being completely lost. The researchers propose that the retained molecules act as structural pillars and electronic modifiers, helping prevent the newly formed oxyhydroxide sheets from agglomerating. The same alkaline environment that drives the battery reactions promotes this reconstruction. Similar hydroxide or oxyhydroxide phases are considered likely for the nickel and copper composites, although direct post-cycling structural confirmation was performed most extensively for cobalt.

Magnetic measurements offered an unusual window into the reconstructed electrodes, indicating that the active hydroxides are locally disordered rather than simple, perfectly ordered crystals. Measurements of magnetic susceptibility showed metal-dependent interactions, including antiferromagnetic correlations, weak ferromagnetic-like behavior, metamagnetic transitions, and magnetic relaxation. The cobalt and nickel hydroxide phases displayed low-temperature features associated with competing or complex interactions, while the copper material showed behavior consistent with antiferromagnetic correlations and a distorted local environment. These observations matter because local disorder can change the electronic states available for binding oxygen intermediates. Valence-band X-ray photoelectron spectra placed the approximate d-band centers in the order nickel below cobalt below copper. Within the commonly used d-band framework, a higher d-band center can strengthen adsorption of oxygen intermediates, helping ORR but potentially making OER less favorable. The results fit that qualitative picture: copper was strongest for ORR, nickel for OER, and cobalt, with an intermediate electronic position, offered the best balance. The authors emphasize that the d-band values are approximate descriptors, not proof of a single causal mechanism.

The work presents coordination polymers as tunable molecular precursors for practical oxygen electrocatalysis, while also highlighting the limits of laboratory battery demonstrations. The cobalt composite approached a zinc-specific capacity of 809.2 milliampere-hours per gram at 5 milliamperes per square centimeter, close to the theoretical value of 820, but the researchers caution that this result reflects a relatively low current density, a high-purity zinc anode, and a particular concentrated alkaline electrolyte. Further studies will be needed to assess operation at higher rates, longer lifetimes, different electrolyte compositions, and larger electrode areas. In situ spectroscopy and density-functional calculations could also test how the retained pyridine, disordered hydroxide structure, and d-band position cooperate during cycling. Even with those questions unresolved, the comparison demonstrates a useful design principle: the best bifunctional catalyst is not necessarily the material that wins either half-reaction independently. In this series, deliberately balancing electronic structure, conductive architecture, and electrochemical reconstruction allowed the cobalt-based pre-electrocatalyst to deliver the most practical zinc-air battery performance.

The precursor strategy also addresses a practical materials challenge beyond catalytic activity. Conventional oxygen electrocatalysts often rely on platinum for reduction or iridium- and ruthenium-based oxides for evolution, but the scarcity and cost of these elements complicate deployment at scale. Nitroprusside coordination polymers offer a different platform because their metal sites, cyanometallate framework, and organic coordination environment can be varied systematically. The cobalt, nickel, and copper comparison therefore functions as a controlled probe of how first-row transition-metal chemistry affects a common molecular architecture, rather than as a simple search for a single universally optimal composition.

That architecture may be especially valuable for studying catalyst reconstruction under realistic operation. Because the electrochemically generated hydroxide is the working phase, evaluating only the pristine powder could obscure the properties that govern a battery’s behavior. The reported combination of spectroscopy, diffraction, microscopy, and magnetic susceptibility illustrates why identifying active materials requires measurements before and after polarization. It also suggests a broader design opportunity: coordination ligands can serve as temporary structure-directing components while influencing the local environment retained after conversion. Determining how much pyridine survives, where it is located, and whether its effect persists over extended cycling will be important for distinguishing a genuine electronic contribution from a short-lived synthesis advantage. Such questions are relevant to translating these composites from proof-of-concept electrodes into durable, scalable air-cathode materials.

Subject of Research: Transition-metal nitroprusside and reduced graphene oxide pre-electrocatalysts for rechargeable zinc-air batteries

Article Title: Pyridine-based nitroprussides coupled to reduced graphene oxide as bifunctional pre-electrocatalysts for zinc-air batteries

Article References: Quintanilla-Serrano, E. A., Acevedo-Peña, P., Ávila, Y., González, M., & Reguera, E. (2026). Pyridine-based nitroprussides coupled to reduced graphene oxide as bifunctional pre-electrocatalysts for zinc-air batteries. Discover Electrochemistry, 3(1), Article 77. https://doi.org/10.1007/s44373-026-00164-9

Image Credits: AI Generated

DOI: 10.1007/s44373-026-00164-9

Keywords: zinc-air batteries, electrocatalysis, reduced graphene oxide, nitroprussides, oxygen reduction, oxygen evolution, cobalt hydroxide, d-band center, Pyridine-based, coupled, reduced, graphene