The study, published in the journal Environmental Geochemistry and Health by a team led by Hongyang Wang of Liaoning University together with colleagues from Northeastern University and Inner Mongolia Yitai Guanglian Coal Chemical, addresses a stubborn technical bottleneck. Coal seam water injection, in which water is pumped into a seam ahead of mining to pre-wet the coal, has long been a frontline dust control strategy. But conventional water struggles to infiltrate the pore and fracture networks of deep coal, especially when mixed metallic substances within the coal matrix block penetration. The result is uneven wetting, dry zones that shatter into inhalable dust during extraction, and suppression rates that fall far short of what occupational health standards demand.

The researchers’ solution is a composite formulation built from three widely available components: sodium gluconate, abbreviated SG, fatty alcohol polyoxyethylene ether known as AEO-3, and sodium fatty alcohol polyoxyethylene ether sulfate, or AES. Each ingredient plays a distinct role. Sodium gluconate, a chelating agent, is capable of binding the metallic substances dispersed in the coal, thereby clearing obstacles that would otherwise impede water movement through the coal’s internal pore structure. AEO-3, a nonionic surfactant, and AES, an anionic surfactant, work in combination to lower the surface tension of the injection solution and reduce the contact angle at the water-coal interface, two of the most important physical parameters governing how readily a liquid spreads across and soaks into a hydrophobic solid surface.

Coal is notoriously water-repellent. Its surface is dominated by hydrophobic carbon structures with relatively few oxygen-containing functional groups, the chemical handles to which water molecules can attach. The SAA formulation changes this chemistry. According to the team’s laboratory characterization, treatment with the agent increased the number of oxygen-containing functional groups on the coal surface, giving water more anchoring points and improving wettability at the molecular scale. At the same time, the surfactants promoted agglomeration of micron-sized coal dust particles, causing individual fine grains to clump into larger, heavier particles that settle out of the air more readily. The effect on particle size distribution was quantifiable: the median particle size, known as the D50 value, increased by 22.58 percent compared with untreated dust.

To test how these microscopic changes translate into real dust control performance, the team constructed a custom dust-suppression simulation system in the laboratory. The apparatus allowed them to generate airborne coal dust under controlled conditions and measure how effectively different spray solutions captured it. When SAA-treated water was used, the effective dust-suppression rate reached 71.50 percent. That figure is 2.17 times the performance of traditional water-mist dust suppression, meaning the formulated agent more than doubled the capture efficiency achievable with plain water alone. For an industrial process where even marginal gains in suppression translate into measurably lower respirable dust exposures for miners, a performance margin of this size is significant.

The most consequential part of the study, however, took place underground. The researchers carried out on-site dust suppression tests at the 3-802 working face of a production coal mine, injecting SAA-treated water into the seam using standard water injection equipment. Before injection, dust sampling established baseline conditions. After treatment, the average coal dust particle size at the face had risen to 2.53 times its pre-injection value, confirming that the agglomeration effect observed in the laboratory survived the journey from bench to bordeline. Larger particles mean less respirable dust, faster settling and cleaner air at the point where miners actually work.

Monitoring across multiple underground measurement points showed total dust suppression rates ranging from 60 to 84 percent, a broad but consistently strong performance envelope that reflects the natural variability of ventilation, mining activity and seam conditions across a working face. Beyond improving air quality, the treatment appeared to influence the mechanical behavior of the coal itself. The team reports that SAA water injection reduced the tendency of the coal to fracture and generate dust, a property linked in earlier research to burst liability, the dangerous propensity of some deep coal seams to fail suddenly and violently. By softening this tendency, the agent may offer a secondary safety benefit against rock bursts and coal bursts, phenomena that remain among the most feared hazards in deep mining.

What distinguishes this work from many prior surfactant studies, the authors argue, is the full chain of evidence it assembles. Laboratory mechanism analysis, surface chemistry characterization, particle size measurement, simulation chamber testing and underground field trials are all presented in a single integrated study, closing the gap that so often separates promising bench chemistry from deployable engineering practice. The funding came from the National Natural Science Foundation of China under grant 52427805, and the work involved authors from Liaoning University’s School of Environmental Sciences, Northeastern University’s School of Resources and Civil Engineering, and Inner Mongolia Yitai Guanglian Coal Chemical, a collaboration that pairs academic environmental science with direct industrial access.

The implications extend beyond a single mine. Deep coal mining is expanding in major producing nations, and occupational dust exposure remains a leading cause of preventable disease among miners, including coal workers’ pneumoconiosis, an incurable and often fatal lung condition. The health burden of coal dust has been documented extensively in the occupational health literature, and regulators continue to tighten permissible exposure limits. Technologies that make existing controls, such as water injection and water sprays, substantially more effective without requiring wholesale redesign of mining equipment are therefore valuable. The SAA formulation uses relatively inexpensive, commercially available chemicals, which the authors suggest positions it for practical engineering application.

Challenges remain before widespread adoption. Field performance will need to be validated across seams of different rank, metamorphic grade and mineralogy, since the wetting behavior of coal varies considerably with its chemical composition. Long-term dosing, environmental discharge and cost at scale will also require scrutiny. Nevertheless, the reported numbers give the approach credibility: a doubling of mist suppression efficiency in the lab, suppression rates of up to 84 percent underground, and a measurable reduction in fracturing tendency all point toward a wetting agent that does more than tweak surface tension. By combining chelation, nonionic and anionic surfactant synergy, and verified field performance, the SAA study offers deep coal mines a concrete new tool in the long-running fight against dust, and offers miners something even more precious: cleaner air at the coal face.

Subject of Research: A composite SAA wetting agent for enhancing coal seam water injection and dust suppression in deep coal mining

Article Title: High-efficiency ‘SAA’ wetting agent for coal mine dust control: from preparation and mechanism to field application

Article References: Wang, H., Zhao, T., Wang, H., Wang, H., Leng, Y., Pan, Y., Xu, L., & Zhu, Y. (2026). High-efficiency ‘SAA’ wetting agent for coal mine dust control: from preparation and mechanism to field application. Environmental Geochemistry and Health, 48(15), Article 600. https://doi.org/10.1007/s10653-026-03491-3

Image Credits: AI Generated

DOI: 10.1007/s10653-026-03491-3

Keywords: coal mining, dust suppression, wetting agent, coal seam water injection, surfactants, deep mining, occupational health, coal dust, sodium gluconate, wettability, Environmental Geochemistry and Health, rock burst