High-temperature superconductivity in B-doped Q-carbon
Researchers at North Carolina State University have significantly increased the temperature at which carbon-based materials act as superconductors, using a novel, boron-doped Q-carbon material.
The previous record for superconductivity in boron-doped diamond was 11 Kelvin, or minus 439.60 degrees Fahrenheit. The boron-doped Q-carbon has been found to be superconductive from 37K to 57K, which is minus 356.80 degrees F.
"Going from 11K to 57K is a big jump for conventional BCS superconductivity," says Jay Narayan, the John C. Fan Distinguished Chair Professor of Materials Science and Engineering at NC State and senior author of two papers describing the work. BCS refers to the Bardeen-Cooper-Schrieffer theory of superconductivity.
Regular conductive materials conduct electricity, but a lot of that energy is lost during transmission. Superconductors can handle much higher currents per square centimeter and lose virtually no energy through transmission. However, superconductors only have these desirable properties at low temperatures. Identifying ways to achieve superconductivity at higher temperatures – without applying high pressure – is an active area of materials research.
To make the boron-doped Q-carbon, the researchers coat a substrate with a mixture of amorphous carbon and boron. The mixture is then hit with a single laser pulse lasting for only a few nanoseconds. During this pulse, the temperature of the carbon is raised to 4,000 Kelvin and then rapidly quenched.
"By incorporating boron into the Q-carbon we eliminate the material's ferromagnetic properties and give it superconductive properties," Narayan says. "So far, every time we have increased the amount of boron, the temperature at which the material retains its superconductive properties has increased.
"This process increases the density of carrier states near the Fermi level," relative to boron-doped diamond, Narayan says.
"The materials advance here is that this process allows a boron concentration in a carbon material that is far higher than would be possible using existing equilibrium methods, such as chemical vapor deposition," Narayan says. "Using equilibrium methods, you can only incorporate boron into Q-carbon to 2 atomic percent – two out of every 100 atoms. Using our laser-based, non-equilibrium process, we've reached levels as high as 27 atomic percent."
That higher concentration of boron is what gives the material its superconductivity characteristics at a higher temperature.
"Oak Ridge National Laboratory has confirmed our findings about higher density of states using electron energy loss spectroscopy," Narayan says.
"We plan to optimize the material to increase the temperature at which it is superconductive," Narayan says. "This breakthrough in high-temperature superconductivity of Q-carbon is scientifically exciting with a path to room temperature superconductivity in novel strongly bonded, light-mass materials. The superconductivity in Q-carbon has special significance for practical applications, as it is transparent, superhard and tough, biocompatible, erosion and corrosion resistant. Nothing like that exists today.
"There are already closed-cycle helium refrigeration systems designed for use with superconductors that can achieve temperatures easily as low as 10K," Narayan says. "B-doped Q-carbon can handle as much as 43 million amperes per square centimeter at 21K in the presence of a two Tesla magnetic field. Since we have demonstrated superconductivity at 57K, this means the doped Q-carbon is already viable for applications."
The most recent paper, "A Novel High-Temperature Carbon-Based Superconductor: B-Doped Q-Carbon," is published in the Journal of Applied Physics. An earlier paper, "High-Temperature Superconductivity in Boron-doped Q-Carbon," is published in the journal ACS Nano. Lead author of both papers is Anagh Bhaumik, a Ph.D. student at NC State. Both papers were co-authored by Ritesh Sachan, a National Research Council postdoctoral researcher at NC State who also works for the Army Research Office.
The research was done with support from the National Science Foundation under grant number DMR-1560838. NC State has filed for a U.S. patent for this technology.
Note to Editors: The study abstracts follow.
"A Novel High-Temperature Carbon-Based Superconductor: B-Doped Q-Carbon"
Authors: Anagh Bhaumik and Jagdish Narayan, North Carolina State University; Ritesh Sachan, North Carolina State University and the Army Research Office Published: July 24, Journal of Applied Physics
Abstract: Following a brief report on high-temperature superconductivity in B-doped Q-carbon, we present detailed structure-property correlations to understand the origin of superconductivity in strongly bonded lightweight materials and methods to further enhance the superconducting transition temperature (Tc). Nanosecond melting of carbon in a super undercooled state and rapid quenching result in strongly bonded unique phase of B-doped Q-carbon. The temperature-dependent resistivity and magnetic susceptibility measurements demonstrate a type II superconductivity in this material with a transition temperature of 36.0±0.5 K and upper critical field of 5.4 T at ~0 K. It has also been shown that in B-doped Q-carbon, the upper critical magnetic field (Hc2(T)) follows Hc2(0) [1-(T/Tc)2.1] temperature dependence and is consistent with the Bardeen-Cooper-Schrieffer formalism. In the present study, B-doped Q-carbon thin films are formed on sapphire substrates by employing pulsed laser annealing using a nanosecond excimer laser. This process involves the rapid quenching of highly undercooled melt of homogenously mixed B and C. Through the structure-property correlation measurements in B-doped Q-carbon, we estimate a higher electronic density of states near the Fermi level. Higher density of states near the Fermi-level along with higher Debye temperature and phonon frequency are responsible for enhanced Tc. As a result of rapid melting and quenching, we can achieve 17.0±1.0 or higher atomic % of B in the electrically active sites of Q-carbon which leads to the formation of shallow electronic states near the valence band maximum. From the critical current density versus field moments, the value of critical current density (Jc (2T)) in B-doped Q-carbon at 21 K is calculated as 4.3×107 Acm-2, which indicates that this novel material can be used for the persistent mode of operation in MRI and NMR applications. This discovery of high-temperature superconductivity in B-doped amorphous Q-carbon shows that non-equilibrium synthesis technique using super undercooling process can be used to fabricate materials with greatly enhanced physical properties.
"High-Temperature Superconductivity in Boron-doped Q-Carbon"
Authors: Anagh Bhaumik and Jagdish Narayan, North Carolina State University; Ritesh Sachan, North Carolina State University and the Army Research Office
Published: April 27, ACS Nano
Abstract: We report high-temperature superconductivity in B-doped amorphous quenched carbon (Q-carbon). This phase is formed after nanosecond laser melting of B-doped amorphous carbon films in a super undercooled state and followed by rapid quenching. Magnetic susceptibility measurements show the characteristics of type-II Bardeen-Cooper-Schrieffer superconductivity with a superconducting transition temperature (Tc) of 36.0±0.5 K for 17.0±1.0 atomic percent boron concentration. This value is significantly higher than the best experimentally reported Tc of 11 K for crystalline B-doped diamond. We argue that the quenching from metallic carbon liquid leads to a stronger electron-phonon coupling due to close packing of carbon atoms with higher density of states at the Fermi level. With these results, we propose that the nonequilibrium undercooling assisted synthesis method can be used to fabricate highly doped materials which provide greatly enhanced superconducting properties.
Related Journal Article